| Title : | Piping and Valves | Doc. No. | L-001 | Annex: | E | Valve Data Sheet | GTGR72C |
| Project : | Company : | Rev.Date : | 20.09.99 | Rev. : | 2 | ||
| Valve Type | End To End Standard | End Type 1 | End Type 2 | End Standard | Size From (in) | Size To (in) | Notes |
| GATE VALVE THROUGH CONDUIT DOUBLE EXPANDING REVERSED PORT | ASME B16.10 | CL | CL | |
2.00 | 6.00 | 020,040 |
| GATE VALVE THROUGH CONDUIT DOUBLE EXPANDING REVERSED PORT | ASME B16.10 | CL | CL | |
8.00 | 12.00 | 022,040 |
| GATE VALVE THROUGH CONDUIT DOUBLE EXPANDING REVERSED PORT | MANUFACTURERS STANDARD | CL | CL | |
14.00 | 14.00 | 022 |
| GATE VALVE THROUGH CONDUIT DOUBLE EXPANDING REVERSED PORT | MANUFACTURERS STANDARD | CL | CL | |
16.00 | 20.00 | 020 |
| Notes | ||
| Pressure Rating | CL 2500 | |
| Design Code | API 6D | 130,136 |
| General Requirement | VSK V403 | |
| Leak Test | VSK V404 | |
| Marking | VSK V003 | |
| Operator | VSK V014 | |
| Low Temp. Appl. | VSK V408 | |
| Max Design Pressure | Barg | 430.9 | 430.8 | 427.1 | 409.9 | 381.4 | 355.3 | 334.9 | 323.0 |
| At Temperature | Deg. C | -101 | 38 | 50 | 100 | 150 | 200 | 250 | 300 |
| Subject/Item | Design and Material Requirement | Material | MDS | EDS |
| BODY/BONNET | Bolted bonnet | ASTM A351 CK-3MCuN A182 F44 |
R16 R14 |
|
| INSIDE TRIM | Double block and bleed. Gate shall be closed in stem rised position | |
|
|
| PORT | Full bore, through conduit, reversed port | |
|
|
| STEM | Rising stem. Outside screw and yoke | A182 F44 | R14 | NIP1 |
| CLOSURE MEMBER | Gate: Double expanding, i.e. expanded in open and closed position; Hardfacing | A182 F44 | R14 | NHF1 NIP1 |
| SEATS | Press fitted seats, full support all around; Hardfacing | A182 F44 | R14 | NHF1 NIP1 |
| SEALS | Packed gland | |
|
|
| STEM PACKING | Expanded graphite not less than 98% purity, or firesafe design according to manufacturer's standard | |
|
|
| OUTSIDE TRIM | |
|
|
|
| BOLTING | Material according to EDS | |
|
NBO2 |
| HANDWHEEL | |
AISI 316 AISI 304 |
|
|
| SPECIAL REQUIREMENTS | Wetted parts suitable for sour service to NACE MR0175 | |
|
|
| 020 | END TYPE ACCORDING TO EDS: NMJ1. |
| 022 | END TYPE ACCORDING TO EDS: NMJ3. |
| 040 | END TO END DIMENSION AS FOR LONG PATTERN, RTJ. |
| 130 | DESIGN SHALL ALSO COMPLY TO ASME B16.34. |
| 136 | SIZES >12" SHALL COMPLY TO ASME B16.34 AND ALL REQUIREMENTS IN API 6D WHICH ARE NOT SIZE DEPENDENT. |