| Title : | Piping and Valves | Doc. No. | L-001 | Annex: | E | Valve Data Sheet | GTFC41B |
| Project : | Company : | Rev.Date : | 20.09.99 | Rev. : | 3 | ||
| Valve Type | End To End Standard | End Type 1 | End Type 2 | End Standard | Size From (in) | Size To (in) | Notes |
| GATE VALVE THROUGH CONDUIT SLAB | API 6D | BE | BE | ASME B16.25 | 2.00 | 24.00 | |
| GATE VALVE THROUGH CONDUIT SLAB | MANUFACTURERS STANDARD | BE | BE | ASME B16.25 | 28.00 | 36.00 | |
| Notes | ||
| Pressure Rating | CL 1500 | |
| Design Code | API 6D | 130,137 |
| General Requirement | VSK V403 | |
| Leak Test | VSK V404 | |
| Marking | VSK V003 | |
| Operator | VSK V401 | |
| Max Design Pressure | Barg | 255.3 | 255.3 | 250.4 | 231.9 | 226.1 | 219.1 | 208.6 | 193.7 |
| At Temperature | Deg. C | -46 | 38 | 50 | 100 | 150 | 200 | 250 | 300 |
| ND (inch) | 2.00 | 3.00 | 4.00 | 6.00 | 8.00 | 10.00 | 12.00 | 14.00 | 16.00 | 18.00 | 20.00 | 24.00 | 28.00 | 30.00 | 36.00 |
| OD (mm) | 60.3 | 88.9 | 114.3 | 168.3 | 219.1 | 273.1 | 323.8 | 355.6 | 406.4 | 457.0 | 508.0 | 610.0 | 711.0 | 762.0 | 914.0 |
| THK (mm) | 11.07 | 15.24 | 17.12 | 21.95 | 25.00 | 28.58 | 33.32 | 35.71 | 40.49 | 45.24 | 50.01 | 59.54 | 68.00 | 65.00 | 75.00 |
| SCH | |
|
|
|
|
160 | 160 | 160 | 160 | 160 | 160 | 160 | |
|
|
| WEIGHT | XXS | XXS | XXS | XXS | |
|
|
|
|
|
|
|
|
|
|
| Subject/Item | Design and Material Requirement | Material | MDS | EDS |
| BODY/BONNET | Bolted bonnet | A352 LCC A350 LF2 |
C12 C11 |
|
| INSIDE TRIM | Bi-directional sealing (by seal on both sides of slab). Gate shall be open in stem rised position | |
|
|
| PORT | Full bore, through conduit | |
|
|
| STEM | Rising stem. Outside screw and yoke; Material according to EDS | |
|
NTR1 |
| CLOSURE MEMBER | Slab gate; Material according to EDS | |
|
NHF1 NTR1 |
| SEATS | Floating seats, pressure energized with spring for sealing at low pressure; Material according to EDS | |
|
NHF1 NTR1 |
| SEALS | Packed gland | |
|
|
| STEM PACKING | Expanded graphite not less than 98% purity, or firesafe design according to manufacturer's standard | |
|
|
| OUTSIDE TRIM | Cavity external bleed plug | |
|
|
| BOLTING | Material according to EDS | |
|
NBO2 |
| HANDWHEEL | |
|
|
|
| SPECIAL REQUIREMENTS | Wetted parts suitable for sour service to NACE MR0175 | |
|
|
| 130 | DESIGN SHALL ALSO COMPLY TO ASME B16.34. |
| 137 | SIZES >24" SHALL COMPLY TO ASME B16.34 AND ALL REQUIREMENTS IN API 6D WHICH ARE NOT SIZE DEPENDENT. |