| Title : | Piping and Valves | Doc. No. | L-001 | Annex: | E | Valve Data Sheet | GTES70B |
| Project : | Company : | Rev.Date : | 20.09.99 | Rev. : | 3 | ||
| Valve Type | End To End Standard | End Type 1 | End Type 2 | End Standard | Size From (in) | Size To (in) | Notes |
| GATE VALVE THROUGH CONDUIT DOUBLE EXPANDING | API 6D | BE | BE | ASME B16.25 | 2.00 | 24.00 | |
| Notes | ||
| Pressure Rating | CL 900 | |
| Design Code | API 6D | 130 |
| General Requirement | VSK V403 | |
| Leak Test | VSK V404 | |
| Marking | VSK V003 | |
| Operator | VSK V401 | |
| Low Temp. Appl. | VSK V408 | |
| Max Design Pressure | Barg | 148.9 | 148.9 | 144.4 | 126.6 | 115.5 | 107.0 | 100.2 | 94.9 |
| At Temperature | Deg. C | -101 | 38 | 50 | 100 | 150 | 200 | 250 | 300 |
| ND (inch) | 2.00 | 3.00 | 4.00 | 6.00 | 8.00 | 10.00 | 12.00 | 14.00 | 16.00 | 18.00 | 20.00 | 24.00 |
| OD (mm) | 60.3 | 88.9 | 114.3 | 168.3 | 219.1 | 273.1 | 323.8 | 355.6 | 406.4 | 457.0 | 508.0 | 610.0 |
| THK (mm) | 5.54 | 7.62 | 8.56 | 10.97 | 15.09 | 18.26 | 21.44 | 23.83 | 26.19 | 29.36 | 32.54 | 38.89 |
| SCH | 80S | 80S | 80S | 80S | 100 | 100 | 100 | 100 | 100 | 100 | 100 | 100 |
| WEIGHT | |
|
|
|
|
|
|
|
|
|
|
|
| Subject/Item | Design and Material Requirement | Material | MDS | EDS |
| BODY/BONNET | Bolted bonnet | ASTM A351 CF3M A182 F316 |
S02 S01 |
|
| INSIDE TRIM | Double block and bleed. Gate shall be open in stem rised position | |
|
|
| PORT | Full bore, through conduit | |
|
|
| STEM | Rising stem. Outside screw and yoke; Material according to EDS | |
|
NTR2 |
| CLOSURE MEMBER | Gate: Double expanding, i.e. expanded in open and closed position; Material according to EDS | |
|
NHF1 NTR2 |
| SEATS | Press fitted seats, full support all around; Material according to EDS | |
|
NHF1 NTR2 |
| SEALS | Packed gland | |
|
|
| STEM PACKING | Expanded graphite not less than 98% purity, or firesafe design according to manufacturer's standard | |
|
|
| OUTSIDE TRIM | |
|
|
|
| BOLTING | Material according to EDS | |
|
NBO2 |
| HANDWHEEL | |
AISI 316 AISI 304 |
|
|
| SPECIAL REQUIREMENTS | Wetted parts suitable for sour service to NACE MR0175 | |
|
|
| 130 | DESIGN SHALL ALSO COMPLY TO ASME B16.34. |