| Title : | Piping and Valves | Doc. No. | L-001 | Annex: | E | Valve Data Sheet | BLGD50B |
| Project : | Company : | Rev.Date : | 20.09.99 | Rev. : | 3 | ||
| Valve Type | End To End Standard | End Type 1 | End Type 2 | End Standard | Size From (in) | Size To (in) | Notes |
| BALL VALVE METAL SEAT REDUCED BORE TOP ENTRY | API 6D 200 MM PUP PIECE | BE | BE | ASME B16.25 | 3.00 | 4.00 | |
| BALL VALVE METAL SEAT REDUCED BORE TOP ENTRY | API 6D 300 MM PUP PIECE | BE | BE | ASME B16.25 | 6.00 | 10.00 | |
| BALL VALVE METAL SEAT REDUCED BORE TOP ENTRY | API 6D 400 MM PUP PIECE | BE | BE | ASME B16.25 | 12.00 | 12.00 | |
| BALL VALVE METAL SEAT REDUCED BORE TOP ENTRY | MANUFAC. STD. 400 MM PUP PIECE | BE | BE | ASME B16.25 | 14.00 | 16.00 | |
| BALL VALVE METAL SEAT REDUCED BORE TOP ENTRY | MANUFAC. STD. 600 MM PUP PIECE | BE | BE | ASME B16.25 | 18.00 | 24.00 | |
| Notes | ||
| Pressure Rating | CL 2500 | |
| Design Code | API 6D | 130,136 |
| Fire Test | API 6FA OR BS 6755 | |
| General Requirement | VSK V405 | |
| Leak Test | VSK V410 | |
| Marking | VSK V003 | |
| Operator | VSK V014 | |
| Max Design Pressure | Barg | 430.9 | 430.9 | 427.1 | 409.9 | 381.4 | 355.3 |
| At Temperature | Deg. C | -46 | 38 | 50 | 100 | 150 | 200 |
| ND (inch) | 3.00 | 4.00 | 6.00 | 8.00 | 10.00 | 12.00 | 14.00 | 16.00 | 18.00 | 20.00 | 24.00 |
| OD (mm) | 88.9 | 114.3 | 168.3 | 219.1 | 273.1 | 323.9 | 355.6 | 406.4 | 457.0 | 508.0 | 610.0 |
| THK (mm) | 11.13 | 13.49 | 21.95 | 25.00 | 32.00 | 36.00 | 40.00 | 40.49 | 45.24 | 50.01 | 59.54 |
| SCH | 160 | 160 | |
|
|
|
|
160 | 160 | 160 | 160 |
| WEIGHT | |
|
XXS | |
|
|
|
|
|
|
|
| Subject/Item | Design and Material Requirement | Material | MDS | EDS |
| BODY/BONNET | Top entry, bolted | A890 J92205 A182 F51 |
D46 D44 |
|
| INSIDE TRIM | Bi-directional sealing (by seal on both sides of ball). Designed for simultaneous full pressure on both sides of closed valve with no pressure in cavity. Double piston effect | |
|
|
| PORT | Reduced bore (additional requirement to API 6D) | |
|
|
| STEM | |
A182 F51 | D44 | NIP1 |
| CLOSURE MEMBER | Trunnion mounted ball (solid); For sizes 6" and below, use material type 316 SS or Nickel alloy 625, both with hardfacing | A182 F51 | D44 | NHF2 NIP1 |
| SEATS | Seat ring; For sizes 6" and below, use material type 316 SS or Nickel alloy 625, both with hardfacing | A182 F51 | D44 | NHF1 NIP1 |
| SPRINGS | |
UNS N0625 UNS N10276 |
|
|
| SEALS | Packed gland (expanded graphite) or lip seal design and fire seal | |
|
|
| LIP SEAL | Material according to EDS | |
|
NSM1 |
| O-RING | |
|
|
|
| FIRE SEAL | Expanded graphite not less than 98% purity | |
|
|
| OUTSIDE TRIM | Body to be fitted with pressure relief valve and cavity external bleed plug of anti-blowout design | |
|
|
| BOLTING | Material according to EDS | |
|
NBO2 |
| SPECIAL REQUIREMENTS | Wetted parts suitable for sour service to NACE MR0175 | |
|
|
| 130 | DESIGN SHALL ALSO COMPLY TO ASME B16.34. |
| 136 | SIZES >12" SHALL COMPLY TO ASME B16.34 AND ALL REQUIREMENTS IN API 6D WHICH ARE NOT SIZE DEPENDENT. |